Ducted reverse cycle, new ducts
The standard swap. A Braemar, Mitsubishi Electric or Hisense outdoor unit, new R1.5 insulated ducts and round ceiling outlets sized to each room. Usually one to two days.
- New R1.5 ducts
- One to two days
- Heats and cools
Many Camberwell homes still run ducted gas heaters installed decades ago. We swap them for reverse cycle that heats in winter and cools in summer, on new insulated ducts, from Braemar, Mitsubishi Electric or Hisense, with an AirTouch 5 zoning controller.
Walk the streets of Camberwell and you see how homes have been added to over the decades: a Federation front, an interwar middle, a 1960s extension out the back. Heating usually came with whichever stage of the house was built last, and in many homes that means an older ducted gas heater, or a wall furnace in a hallway, well past its best. For heating and cooling Camberwell homes usually need one thing: a system sized to the house as it is now, not as it was when the heater went in.
Reverse cycle heats for around a third of the running cost of gas heating, and it cools in summer from the same outdoor unit. For a ducted gas swap our default is new R1.5 insulated ducts sized to the new unit, typically one to two days of work. Where a double-storey layout means the ducts cannot be replaced, a Braemar Dominator can keep the existing ducts and control the airflow through them. Split systems suit extensions, studies and rooms the old ducts never reached, and take a few hours each.
We do not repair old gas heaters, we replace them, and the old unit comes out as part of the job. If the plan is to move the whole house off gas over time, we can sequence this with hot water, solar and a battery as part of the work we do across Camberwell.
The right option depends on the ducts, the floor plan and how many zones you want.
The standard swap. A Braemar, Mitsubishi Electric or Hisense outdoor unit, new R1.5 insulated ducts and round ceiling outlets sized to each room. Usually one to two days.
Used only where the existing ducts cannot be replaced, which is mostly double-storey homes with ducts that are hard to reach. It uses the existing ducting and controls airflow through it.
Rear extensions, studies and converted rooms often sit outside the old duct run. A wall-mounted split heats and cools one room efficiently and takes a few hours.
A wall touchscreen that opens and closes ducted outlets room by room, so you heat the bedrooms at night and the living area by day instead of the whole house.
The full range is on our products page.
Ducted reverse cycle, including the Dominator for homes where the existing ducts have to stay.
Ducted units for tight roof spaces, plus split and multi-head systems.
Ducted and split systems, with anti-corrosive Golden Fin coils on the ducted range.
Zoning control for ducted systems, with a sensor in each zone and control from your phone.
We have no written-up heating job in Camberwell yet. These three show the three main routes: splits, new ducts and the Dominator exception.
Next door to Camberwell, two worn split systems were replaced and a condensation pump added during a 12.35kW solar and 24.18kWh battery install, with an iStore heat pump for hot water.
On the south-east side of Melbourne, a 23.5kW ducted reverse cycle system on R1.5 insulated ductwork with 16 outlets and six AirTouch 5 zones, so each part of the house is controlled on its own.
In this Berwick home the old ductwork stayed, so a Braemar Dominator took the place of the gas heater and pushes air through the original vents. Temperature sensors in each zone keep the rooms even.
A ducted swap is typically one to two days. Splits take a few hours each.
We inspect the existing heater, the ducting where it can be reached, the roof space and where the outdoor unit can sit.
Ducted on new R1.5 ducts, a Dominator where ducts cannot be replaced, or splits, with AirTouch 5 zoning if you want it.
Equipment, ducts, electrical work, removal of the old heater and the Victorian Energy Upgrades discount in one written price.
Our own licensed team removes the gas heater, fits the new unit, runs ducts and circuits, and commissions the system.
We set up the controller, walk you through zoning and issue the compliance paperwork before we leave.
The main incentive on heating and cooling is a Victorian discount, applied on the quote for you.
The VEU discount applies to reverse cycle heating and cooling, and it is largest when you are replacing gas heating. We lodge it and take it off at point of sale.
Reverse cycle heats for around a third of the running cost of gas heating. Add solar and the daytime running cost drops further. See solar and battery in Camberwell for how that fits.
The quote includes the electrical work, the ducts or pipework and removal of the old unit, so the price you accept is the price you pay.
A heating swap is one of the bigger jobs in a house, and it is worth knowing who is doing it.
ARC licence AU 065299 for refrigerant work and A-Grade electricians on the same crew.
We replace ducts with insulated R1.5 and only keep old ones when there is no alternative.
Braemar, Mitsubishi Electric and Hisense, matched to the house rather than pushed from a single supplier.
Heating, hot water, solar and a battery can all line up if you want to leave gas behind.
Live Google reviews. Look for the ducted reverse cycle and AirTouch jobs.
Common questions from Camberwell homeowners replacing gas heating.
If it is old, running costs and reliability are the usual reasons. We replace rather than repair, and a swap before it fails lets you choose the timing instead of the heater choosing for you.
Our default is new R1.5 insulated ducts sized to the new unit. We only keep existing ducts, using a Braemar Dominator, where they cannot be replaced, which is usually in double-storey homes.
Typically one to two days with new ducts. A split system takes a few hours.
Yes. The AirTouch 5 controller zones the ducted outlets room by room, so closed-off bedrooms do not take heat while the living area does.
Yes. We inspect what is there, plan the outdoor unit position and ducting around the roof space, and use splits for rooms the old system never reached.
Braemar, Mitsubishi Electric and Hisense for heating and cooling, with the AirTouch 5 zoning controller where ducted zoning is wanted.
Book a free inspection or send photos of your heater, roof space and switchboard. You get one fixed price with the discount taken off.